New Pentek Board Synchronizes Up to 256 Channels for Military, Medical Imaging and Beamforming Applications
*Synchronizes up to 8 Cobalt or Onyx SDR boards at sample rates to 800 MHz *Synchronous sampling, gating and triggering for up to 64 boards *PCIe form factor targets low cost PC-based systems *Supports multi-channel phase-coherent applications such as beamforming
Upper Saddle River, NJ, June 29, 2012 --(PR.com)-- Pentek, Inc., today introduced a system synchronization and distribution amplifier, the Model 7893 PCIe board. This synchronizer is designed to support up to 8 Pentek Virtex-6 Cobalt® and Pentek Virtex-7 Onyx™ boards at sample clock rates up to 800 MHz. In the cascade mode, up to eight 7893 boards can be linked to allow 64 Onyx or Cobalt boards to receive a common clock along with timing signals for synchronizing, triggering and gating functions.
Synchronization is important in multichannel applications such as phased array radar, diversity receivers, and direction finding and beamforming antennas. These applications abound in military systems, but the same concepts are also used in medical imaging and industrial inspection systems where beamforming improves the image resolution.
“New beamforming applications call for higher channel counts with precise sampling, gating and triggering synchronization across all channels,” said Rodger Hosking, vice president of Pentek. “The cascadable design of the 7893 delivers a proven and systematic solution for synchronizing up to 64 boards and up to 256 channels to form large arrays very efficiently. This product saves our customers precious development time during system integration,” he added.
The Model 7893 enables synchronous sampling and timing for a wide range of multichannel high-speed data acquisition, DSP and software radio applications.
Supporting Features and Products
The Model 7893 is a single-slot PCIe board that uses the slot solely for physical mounting with no electrical connections; power is supplied through a standard six-pin PCIe power connector.
The 7893 accepts a user supplied external clock from a front-panel subminiature version A (SMA) connector, from the input low-voltage positive emitter-coupled logic timing bus, or from the on-board programmable voltage controlled crystal oscillator (VCXO). The VCXO can operate alone or can be phase-locked to a system reference clock signal. Each 7893 has four programmable clock outputs available via SMA connectors on the front panel for distribution of sample clocks to other boards.
Operational parameters for the 7893 are programmed through the universal serial bus (USB) port, including VCXO frequency, clock dividers and delays, so the user can make timing adjustments on the gate and synchronize signals before they are sent to buffers for output through eight timing bus connectors. The USB port can also be used to generate gate/trigger and sync/pulse-per second signals for distribution to all connected boards.
Pentek’s ReadyFlow board support packages include functions for initialization and control of sample and reference clocks and clock routing, as well as example code for multiboard synchronization. ReadyFlow board support packages are available for Windows, Linux and VxWorks operating systems.
Pricing and Availability
For the latest pricing and availability information, please contact Mario Schiavone by phone at (201) 818-5900 ext.229, or by email at mario@pentek.com.
About Pentek
Pentek develops, manufactures and markets innovative DSP systems and recorders to original equipment manufacturers, distributors and value-added resellers. Pentek offers powerful VME, VPX, VXS, PMC, XMC, cPCI, PCI, PCIe and AMC boards for data acquisition, software radio and digital signal processing featuring Texas Instruments C6000 DSPs, Freescale G4 PowerPCs and Xilinx FPGAs. Pentek's I/O includes A/Ds, D/As, FPGAs, digital up/downconverters and more. Pentek equips all products with high-performance I/O including gigabit serial interfaces and offers strong DSP software support.
Pentek, Cobalt, Onyx and ReadyFlow are trademarks or registered trademarks of Pentek, Inc. Brand or product names are registered trademarks or trademarks of their respective holders.
For access to the release and data sheets, please visit: http://www.pentek.com/whatsnew/viewrelease.cfm?index=163
North American Sales Contact: Mario Schiavone, Pentek, Inc., One Park Way, Upper Saddle River, NJ 07458-2311; Telephone 201-818-5900, ext. 770; Fax 201-818-5904; Email news@pentek.com; Website www.pentek.com.
International Sales Contacts: Galleon Embedded Computing in Germany at (49) 89 5908 2101, LVD Systems in Italy at (39) 011 966 1319, RECAB AB in Sweden at (46) 8 6830300, Advanced Embedded Systems in the UK, Spain and Portugal at (44) 0 1202 885 675, Sela Electronic Systems in Israel at (972) 3 6479969,MISH International in Japan at (81) 42-538-7650, Beijing Betaone Sysjob Ltd. in China at (86) 10 82784106 and Acetronix Co. Ltd. in Korea at (82) 24202343, ext. 106, Dynamic C4 Pte. Ltd. In Singapore, Malaysia and Indonesia at (65) 6405 4506. For a list of Pentek representatives and distributors, please visit http://www.pentek.com/contact/replist.pdf.
Media Contact:
Barbara Stewart
Patterson & Associates
480-488-6909
barbara@patterson.com
Synchronization is important in multichannel applications such as phased array radar, diversity receivers, and direction finding and beamforming antennas. These applications abound in military systems, but the same concepts are also used in medical imaging and industrial inspection systems where beamforming improves the image resolution.
“New beamforming applications call for higher channel counts with precise sampling, gating and triggering synchronization across all channels,” said Rodger Hosking, vice president of Pentek. “The cascadable design of the 7893 delivers a proven and systematic solution for synchronizing up to 64 boards and up to 256 channels to form large arrays very efficiently. This product saves our customers precious development time during system integration,” he added.
The Model 7893 enables synchronous sampling and timing for a wide range of multichannel high-speed data acquisition, DSP and software radio applications.
Supporting Features and Products
The Model 7893 is a single-slot PCIe board that uses the slot solely for physical mounting with no electrical connections; power is supplied through a standard six-pin PCIe power connector.
The 7893 accepts a user supplied external clock from a front-panel subminiature version A (SMA) connector, from the input low-voltage positive emitter-coupled logic timing bus, or from the on-board programmable voltage controlled crystal oscillator (VCXO). The VCXO can operate alone or can be phase-locked to a system reference clock signal. Each 7893 has four programmable clock outputs available via SMA connectors on the front panel for distribution of sample clocks to other boards.
Operational parameters for the 7893 are programmed through the universal serial bus (USB) port, including VCXO frequency, clock dividers and delays, so the user can make timing adjustments on the gate and synchronize signals before they are sent to buffers for output through eight timing bus connectors. The USB port can also be used to generate gate/trigger and sync/pulse-per second signals for distribution to all connected boards.
Pentek’s ReadyFlow board support packages include functions for initialization and control of sample and reference clocks and clock routing, as well as example code for multiboard synchronization. ReadyFlow board support packages are available for Windows, Linux and VxWorks operating systems.
Pricing and Availability
For the latest pricing and availability information, please contact Mario Schiavone by phone at (201) 818-5900 ext.229, or by email at mario@pentek.com.
About Pentek
Pentek develops, manufactures and markets innovative DSP systems and recorders to original equipment manufacturers, distributors and value-added resellers. Pentek offers powerful VME, VPX, VXS, PMC, XMC, cPCI, PCI, PCIe and AMC boards for data acquisition, software radio and digital signal processing featuring Texas Instruments C6000 DSPs, Freescale G4 PowerPCs and Xilinx FPGAs. Pentek's I/O includes A/Ds, D/As, FPGAs, digital up/downconverters and more. Pentek equips all products with high-performance I/O including gigabit serial interfaces and offers strong DSP software support.
Pentek, Cobalt, Onyx and ReadyFlow are trademarks or registered trademarks of Pentek, Inc. Brand or product names are registered trademarks or trademarks of their respective holders.
For access to the release and data sheets, please visit: http://www.pentek.com/whatsnew/viewrelease.cfm?index=163
North American Sales Contact: Mario Schiavone, Pentek, Inc., One Park Way, Upper Saddle River, NJ 07458-2311; Telephone 201-818-5900, ext. 770; Fax 201-818-5904; Email news@pentek.com; Website www.pentek.com.
International Sales Contacts: Galleon Embedded Computing in Germany at (49) 89 5908 2101, LVD Systems in Italy at (39) 011 966 1319, RECAB AB in Sweden at (46) 8 6830300, Advanced Embedded Systems in the UK, Spain and Portugal at (44) 0 1202 885 675, Sela Electronic Systems in Israel at (972) 3 6479969,MISH International in Japan at (81) 42-538-7650, Beijing Betaone Sysjob Ltd. in China at (86) 10 82784106 and Acetronix Co. Ltd. in Korea at (82) 24202343, ext. 106, Dynamic C4 Pte. Ltd. In Singapore, Malaysia and Indonesia at (65) 6405 4506. For a list of Pentek representatives and distributors, please visit http://www.pentek.com/contact/replist.pdf.
Media Contact:
Barbara Stewart
Patterson & Associates
480-488-6909
barbara@patterson.com
Contact
Pentek, Inc.
Mario Schiavone
201-818-5900
www.pentek.com
To schedule an interview with Rodger Hosking, please contact Patterson & Associates.
Mario Schiavone
201-818-5900
www.pentek.com
To schedule an interview with Rodger Hosking, please contact Patterson & Associates.
Contact
Categories